Yamaha Diagnostic Software Driver
The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modified without permission of the copyright owner. The SOFTWARE may not be used to distribute illegal data or data that violates public policy, nor may you initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation. YAMAHA'S ENTIRE OBLIGATIONS HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF. IN NO EVENT SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH SOFTWARE, EVEN IF YAMAHA OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR ANY CLAIM BY ANY OTHER PARTY.
Does anyone know why I cannot load the usb driver for my YDS. Yamaha Diagnostic Software Problems Hi Mitch, Yes it is the same one to the number. When updating the driver, uninstall the driver by double-clicking 'setup.exe' for the latest driver, restart your computer, and then install the latest driver. If Yamaha software does not operate properly, uninstall and install the software again. For 2012 & on models the yamaha YDS2 kit is needed The kit comes with the USB interface with custom moulded engine harness plug, Yamaha 1.33 software,YDS manual & full installation instructions with easy install CD.
On the 2015s the YDIS couplers are located in the driver's helm compartment. The YDIS couplers are identified by 'DIAGP' tag (port engine) or 'DIAGS' tag (starboard engine) on the deck wire harness. • Plug in the YDS cable to your engine. • Start your engine (or just bump the starter enough to get a reading) • Turn on the water to your engine (only if you start the engine) • Plug in the USB plug into your computer • One time only step--you should get a 'New Hardware' message.if the disk is still in the drive, it will find the drivers. If it is not, then browse to C: Program Files YDS Driver • Launch the YDS software. • Hit Enter it should says something about communicating to the ECM.
We have members with boats from all the major manufacturers including Yamaha, Seadoo, Scarab and Chaparral. We don't email you SPAM, and the site is totally non-commercial. So what's to lose?
It is required to unify the system version to V3 or V4 by upgrading/downgrading DME Designer or firmware. • Since this software was not designed to be operated via a touch panel in Windows 10/8, we cannot guarantee operation via a touch panel. DME Designer Version Firmware Version DME-N, ICP1 DME Satellite SP2060 4.0.1, 4.0.0 4.06, 4.05, 4.04, 4.03, 4.02, 4.01, 4.00 4.06, 4.05, 4.04, 4.03, 4.02, 4.01, 4.00 1.33, 1.32, 1.31, 1.30, 1.24, 1.23, 1.22, 1.21 * DME Series firmware V4.05 or later is needed for DME to connect to a Windows 10 PC that is installed with DME Designer. Main Revisions and Enhancements Improvements • Now supports Windows 10.
(It also gets rid of this banner!). Ever wonder what your engine hours are, how to read them, if your engine threw errors?
Welcome to Jetboaters.net! We are delighted you have found your way to the best Jet Boaters Forum on the internet! Please consider so that you can enjoy all the features and offers on the forum. We have members with boats from all the major manufacturers including Yamaha, Seadoo, Scarab and Chaparral. We don't email you SPAM, and the site is totally non-commercial.
DME Designer Combo Installer V4.0.1 for Win 10/8.1/8/7/Vista/XP Important Notice • Save an up-to-date DME project file (*.daf). Don't update unless an up-to-date '.daf' file has already been saved on your computer.
If none of these helps, you can for further assistance.
Without the 'daf' file, you will not be able to restore DME operation. • If you update with using the following conditions, DME Designer may not operate properly. A) If you are using DME-N Network Driver V1.2.0 and DSP5D/LS9/M7CL Editor. B) If you are using DME-N Network Driver V1.1.3 or V1.1.2. When updating the driver, uninstall the driver by double-clicking 'setup.exe' for the latest driver, restart your computer, and then install the latest driver. If Yamaha software does not operate properly, uninstall and install the software again. • DME Designer V4 cannot design/control the system that consists of DME Firmware V3 units or the mixed system with Firmware V3 and V4 units.
At the moment it appears there is no available software to access these boats. (on some kits sold on EBAY, it has 2 disks.one for the YDS, and one for the cable driver--install BOTH) • Update the DB on the software (launch the SW and press F1) • Make sure the cable is on COM Port 1. • Locate your connection point on the engine. If you have a 2006 or less, it will be behind the cover plate in the rear starboard storage locker (yeah who would have thunk!). On 2007+ 230's it is behind the plate on the starboard side of the engine compartment. On 210s, it is tucked into the wiring harness over the top of the port engine. It will have one red wire on one side of the plug and 3 or 4 wires on the side you will plug into.
You dont' have to actually start the engine, so you don't need to hook up to a water supply to read the YDS. Follow the same steps outlined by Julian, except instead or starting the engine, just 'bump' the starter. This gets the communication going between the ECM, the USB dongle, and the YDS software on laptop. The engine does not have to be running and therefore you don't need to have access to water and that makes it much easier to do in many cases.
Yamaha Outboard Motor Diagnostic Software
• Shut off the water • Turn off the engine Repeat for other engine. There are lots of other things this software can do, but that is for another day. Here is what it read as an example for my engine hours: Engine speed Time[h] - 2000 r/min - 4000 r/min - 6000 r/min 7.4 6000 - 8000 r/min - 10000 r/min 11.2 10000 - 12000 r/min 0.99 Total hours of operation 132 Attached is a copy of the file you can create and save from the software. Click to expand.Here's a little tip for those of you using the YDS software. Easycap driver windows 10. You dont' have to actually start the engine, so you don't need to hook up to a water supply to read the YDS. Follow the same steps outlined by Julian, except instead or starting the engine, just 'bump' the starter.
Yamaha YDS/YDIS Diagnostics New YDS PRO kit V1.33 compatable with windows 7/8/10 Works on all waverunner & Outboard to year 2011 To Order or Enquire please email us: with your Order please advise your location/ZIP so we can check the best shipping options DHL/TNT/UPS Unique easy install windows ( see images!!) and auto install of interface drivers!!! The kit comes with everything you need to connect YDS to any of the ECU controlled Yamaha personal watercraft, Jetboats & EFI Outboard Motors upto year 2011. Please check the applications charts below for any exceptions, for 2012 & on models the yamaha YDS2 kit is needed The kit comes with the USB interface with custom moulded engine harness plug, Yamaha 1.33 software,YDS manual & full installation instructions with easy install CD Laptop hardware requirements are: 32/64 Bit operating system PC/laptop, an available USB port, a DVD/CD-ROM drive for the YDS software installation. The Microsoft Excel program is only needed if you want to save and export engine monitoring data. YDS does not work with MAC computers!!!
I question the ability of the early versions do do this on the newest boats, because the ECM's have different parameters. Over the years, we have had several Yamaha techs that used the software for a living, comment on the capability of the software. But the gray area happened with the newer boats as Yamaha tried to control the distribution and use of their software once again. It would be a good discussion and thread to have those with experience using this software on the 1.8L boats, and the newest 210 line, to discuss their experiences.
Q: Why my YAMAHA Diagnostic System WinUSB Driver doesn't work after I install the new driver? Please identify the driver version that you download is match to your OS platform. You should uninstall original driver before install the downloaded one. Try a driver checking tool such as. As there are many drivers having the same name, we suggest you to try the Driver Tool, otherwise you can try one by on the list of available driver below. Please scroll down to find a latest utilities and drivers for your YAMAHA Diagnostic System WinUSB Driver. Be attentive to download software for your operating system.
• Plug in the YDS cable to your engine. • Start your engine (or just bump the starter enough to get a reading) • Turn on the water to your engine (only if you start the engine) • Plug in the USB plug into your computer • One time only step--you should get a 'New Hardware' message.if the disk is still in the drive, it will find the drivers.
*This combo installer includes DME Designer and DME-N Network Driver *DME-N Network Driver is updated to V1.2.3 to support Windows 10.(The current DME Designer V4.0.0 already supports Windows 10.) If the current version 4.0.0 of DME Designer is already installed on your PC, the installation of DME Designer will be skipped and only DME-N Network Driver V1.2.3 will be installed. System Requirements.
[Compatible] RIVAGE PM Editor [Compatible] CL Editor [Compatible] Yamaha Console Extension (ex.
So what's to lose? Membership allows you to ask questions (no matter how mundane), meet up with other jet boaters, see full images (not just thumbnails), browse the member map and qualifies you for members only discounts offered by vendors who run specials for our members only! (It also gets rid of this banner!). Dave, it refers to the same diagnostics program to read/troubleshoot/test/diagnose the ECM and engine systems on our boats. However, the early boats did use the term YDS as the acronym for Yamaha Diagnostic System. In 2010, the 240 line was introduced and the software that compromised the YDS system was changed from version 1.2 to 1.33.
I purchased my cables and software on eBay for about $75. This thread describes it's use perfectly and I was able to pull info from both engines. I also wanted to chime in and say that I used a Microsoft Surface Pro (version 1) with Microsoft Windows 8.1. I did have to go to the device manager and force the driver on the disk for the cable (and the 32bit one, I believe even though my OS is 64bit). I then changed the COM port to COM1 and that setting stuck upon removing/reinserting the cable (not connected to an engine). I did all of this before connecting to anything and I had zero issues when the time came to use it a few days later. Here's a little tip for those of you using the YDS software.
This gets the communication going between the ECM, the USB dongle, and the YDS software on laptop. The engine does not have to be running and therefore you don't need to have access to water and that makes it much easier to do in many cases.
1.33 was then referred to as YDIS. It is reported that 1.2 could still be used on the 2010 1.8L boats. But 1.33 was the new version to use that had new features for use on the newer boats and also would run diagnostics on the earlier boats. Much of this was done because the software had been distributed to the dealer network and beyond. Yamaha likes control.
If it says it failed to communicate to the ECM, then either your driver didn't install or you aren't plugged in the proper sequence, or your cable isn't assigned to com port 1. • Hit enter and you should have a complete menu of items you can look. For Engine hours click on 'Data Logger' and then click on 'Engine Operating Hours according to engine speed' • If you wish to save the hours, click F2 to save the file (it saves as a.csv file or a 'Comma Separated Value' file and an.xls file.in a nutshell.a file Excel can read, or most any data application like Notepad, wordpad etc.) • If you want to check out and see if you have had any engine 'errors', click on the 'Diagnosis', and then on 'Diagnosis Record'.
YAMAHA Diagnostic System WinUSB Driver is a windows driver. Common questions for YAMAHA Diagnostic System WinUSB Driver Q: Where can I download the YAMAHA Diagnostic System WinUSB Driver's driver? Please download it from your system manufacturer's website. Or you download it from our website.
(on some kits sold on EBAY, it has 2 disks.one for the YDS, and one for the cable driver--install BOTH) • Update the DB on the software (launch the SW and press F1) • Make sure the cable is on COM Port 1. • Locate your connection point on the engine. If you have a 2006 or less, it will be behind the cover plate in the rear starboard storage locker (yeah who would have thunk!). On 2007+ 230's it is behind the plate on the starboard side of the engine compartment.
Is correct, the common reference for the system is YDS which stands for Yamaha Diagnostic Software. But with the advent of the 1.8L engine, they changed the term to YDIS and stopped describing it and only referencing it as 'diagnostics'. It appears to be the same manual, just rewritten to reflect nomenclature changes, but the software has to have changed to allow it to control the new systems. I am sure that you can probably read engine hours and time/rpm info and more with the old YDS on the new boats, but I don't know about it being used fully in them. Clear as mud? I have just successfully used this software to read the engine hours and diagnostics of a used boat I was looking.
Welcome to Jetboaters.net! Judge dredd comic books. We are delighted you have found your way to the best Jet Boaters Forum on the internet! Please consider so that you can enjoy all the features and offers on the forum.
Membership allows you to ask questions (no matter how mundane), meet up with other jet boaters, see full images (not just thumbnails), browse the member map and qualifies you for members only discounts offered by vendors who run specials for our members only! (It also gets rid of this banner!). Ever wonder what your engine hours are, how to read them, if your engine threw errors? Well first of all you will need some software (YDS 1.3) and a Cable (Ebay is a good source). Once you have that, here is the process from start to finish of what you need to do: • Install the software 1.33 for 2012 or before models. It looks as if you need YDIS 2.13 for 2013 and newer boats.
• Hit enter and you should have a complete menu of items you can look. For Engine hours click on 'Data Logger' and then click on 'Engine Operating Hours according to engine speed' • If you wish to save the hours, click F2 to save the file (it saves as a.csv file or a 'Comma Separated Value' file and an.xls file.in a nutshell.a file Excel can read, or most any data application like Notepad, wordpad etc.) • If you want to check out and see if you have had any engine 'errors', click on the 'Diagnosis', and then on 'Diagnosis Record'. • Shut off the water • Turn off the engine Repeat for other engine. There are lots of other things this software can do, but that is for another day. Here is what it read as an example for my engine hours: Engine speed Time[h] - 2000 r/min - 4000 r/min - 6000 r/min 7.4 6000 - 8000 r/min - 10000 r/min 11.2 10000 - 12000 r/min 0.99 Total hours of operation 132 Attached is a copy of the file you can create and save from the software. Click to expand.Here's a little tip for those of you using the YDS software.
Well first of all you will need some software (YDS 1.3) and a Cable (Ebay is a good source). Once you have that, here is the process from start to finish of what you need to do: • Install the software 1.33 for 2012 or before models. It looks as if you need YDIS 2.13 for 2013 and newer boats. At the moment it appears there is no available software to access these boats.
You dont' have to actually start the engine, so you don't need to hook up to a water supply to read the YDS. Follow the same steps outlined by Julian, except instead or starting the engine, just 'bump' the starter. This gets the communication going between the ECM, the USB dongle, and the YDS software on laptop. The engine does not have to be running and therefore you don't need to have access to water and that makes it much easier to do in many cases.
• Since this software was not designed to be operated via a touch panel in Windows 10/8, we cannot guarantee operation via a touch panel. DME Designer Version Firmware Version DME-N, ICP1 DME Satellite SP2060 4.0.1, 4.0.0 4.06, 4.05, 4.04, 4.03, 4.02, 4.01, 4.00 4.06, 4.05, 4.04, 4.03, 4.02, 4.01, 4.00 1.33, 1.32, 1.31, 1.30, 1.24, 1.23, 1.22, 1.21 * DME Series firmware V4.05 or later is needed for DME to connect to a Windows 10 PC that is installed with DME Designer. Main Revisions and Enhancements Improvements • Now supports Windows 10. *This combo installer includes DME Designer and DME-N Network Driver *DME-N Network Driver is updated to V1.2.3 to support Windows 10.(The current DME Designer V4.0.0 already supports Windows 10.) If the current version 4.0.0 of DME Designer is already installed on your PC, the installation of DME Designer will be skipped and only DME-N Network Driver V1.2.3 will be installed. System Requirements.
DME Designer Combo Installer V4.0.1 for Win 10/8.1/8/7/Vista/XP Important Notice • Save an up-to-date DME project file (*.daf). Don't update unless an up-to-date '.daf' file has already been saved on your computer. Without the 'daf' file, you will not be able to restore DME operation. • If you update with using the following conditions, DME Designer may not operate properly.
A) If you are using DME-N Network Driver V1.2.0 and DSP5D/LS9/M7CL Editor. B) If you are using DME-N Network Driver V1.1.3 or V1.1.2.
We don't email you SPAM, and the site is totally non-commercial. So what's to lose? Membership allows you to ask questions (no matter how mundane), meet up with other jet boaters, see full images (not just thumbnails), browse the member map and qualifies you for members only discounts offered by vendors who run specials for our members only!
File(size) (7.37MB) Version Windows 8/7/Vista /XP：V.3.1.3、2000：V.2.3.3 Update 2012/08/21 Platform Windows 8 (SP0)/Windows 7 (SP0/SP1)/Windows Vista (SP2)/Windows XP Professional (SP3)/XP Home Edition (SP3)/2000 (SP4) CPU XP/2000:166MHz, Vista:800MHz, Windows8/7:1.4GHz or higher; Intel Core/Pentium/Celeron processor *Mobile CPUs (like ATOM) are not supported. Hard disk space 10MB or more Memory XP/2000:32MB or more (64MBor more is recommended), Vista:512MB or more, Windows8/7:1GB or more Other This USB-MIDI Driver is for 32bit Windows only. Please dowload USB-MIDI Driver for Windows 8/7/Vista/XP 64bit, if you use 64bit Windows. USB-MIDI Driver for Windows® 8/7/Vista/XP 64bit.
Welcome to Jetboaters.net! We are delighted you have found your way to the best Jet Boaters Forum on the internet! Please consider so that you can enjoy all the features and offers on the forum. We have members with boats from all the major manufacturers including Yamaha, Seadoo, Scarab and Chaparral.
File(size) (7.39MB) Version V.3.1.3 Update 2012/08/21 Platform Windows 8 (SP0)64bit, Windows 7 (SP0/SP1)64bit, Windows Vista (SP2) 64bit, Windows XP Professional/Home Edition (SP3) 64bit CPU Intel 64 compatible processor *Mobile CPUs (like ATOM) are not supported. Hard disk space 10MB or more Memory XP:256MB or more, Vista:512MB or more, Windows8/7:2GB or more Other This USB-MIDI Driver is for 64bit Windows only. Please dowload USB-MIDI Driver for Windows 8/7/Vista/XP 32bit, if you use 32bit Windows. USB-MIDI Driver for Windows(R) Me/98. You are only permitted to use this software program pursuant to the terms and conditions of the attached Software License Agreement ('Agreement'). It is an agreement between you (as individual or a legal entity) and Yamaha Corporation ('Yamaha').